PTCL introduces DSL service for our valued subscribers. We are committed to provide you quality internet services. Please follow the installation instructions and log on to your ADSL broadband link.
Step 1: Connecting to the Splitter, Power Connection & LAN cable.
- Line hole connects to PTCL wire or Wall phone Jack (RJ-11 Jack).
- Modem hole connects to the DSL jack of the ADSL CPE (Customer Premises Equipment).
- Phone hole connects to a telephone set.
- Connect the Power Adapter to the AC power plug and attach the connector of adapter to the CPE and switch it on.
- Attach one end of LAN wire (RJ-45) to the LAN interface of CPE and the other end to the LAN wire to the LAN interface of computer’s LAN card.
- Link Indicator lights will lit up and show the connectivity. ADSL light will start. blinking and soon will be static as a sign of connectivity with our system, if the line is properly jumpered in PTCL premises with the DSLAM (Digital Subscriber Line Access Multiplexer).Joint less and direct cable line from the nearest PTCL pole or cabinet must be connecting to your splitter and then all the phone extensions must be taken from the phone hole of splitter. The Drop wire distance from PTCL pole or Cabinet must not be ideally more than 50 meters.(Twisted pair wire can be longer)
Step 2: ADSL Configuration in CPE and Computer
1. Go to Start Menu < Control Panel < Network and Internet Connections < Network Connections. Check that the Local Area Connection is enabled. Right click local Area network and click properties. Following window will be shown.
 |
| ADSL Configuration in CPE and Computer |
 |
| ADSL Configuration in CPE and Computer |
2. Double click “internet protocol (TCP/IP)”, Check “Use the following IP address” and make the following settings:
IP Address: 192.168.1.3
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
Then, check “Use the following DNS server addresses” and make the following settings:
Preferred DNS Server: 203.99.163.240
Alternate DNS Server: 203.135.0.170
 |
| DNS Server |
3. Now open Internet Explorer and write “192.168.1.1” in address bar and press enter. There must not be any proxy setting in the internet Explorer.
 |
| Internet Explorer |
A small pop up window will open as shown in the figure below and ask ”User Name” and “Password” for opening the CPE’s interface.
Enter User Name: ZXDSL and Password: ZXDSL and press OK.
Note: “Both username & password must be written in capital letters.”
 |
| ZXDSL AND PASSWORD SETTING |
4. CPE configuration will be opened. This will show Modem Status. Click the
Connection Setting.
 |
| Modem Status |
5. Connection Settings show current active connection as shown in the figure. Click
create new connection service.
 |
| create new connection service |
6. In create new connection window. Select “
PPP over Ethernet”
 |
| PPP over Ethernet |
7. Enter VPI=0 and VCI=103 for Copper number &
VPI=8 and VCI=81 for ONU Fiber
Optics number. Select Authentication protocol as “PAP” and enter username and Password. Click “Create this new service”.
 |
| VPI AND VCI SETTINGS |
8. Now Connection settings window will be opened and shows current active
connections.
 |
| connection settings |
9. Click Advance settings and then on Security. Security Interface Configuration is
shown. Click Add Interface.
 |
| click add interface |
10. Following figure will be shown. Click Apply.
 |
security add interface
|
11. Security Interface Configuration will be opened. Click Enable NAT to interface.
 |
Security Interface Configurations
|
12. Following window will be opened.
 |
| security interface window |
13. Click System Settings and then on DHCP Server. In DHCP Server Configuration,
Click on Enable DHCP Server and Apply.
 |
| Enable DHCP Server |
14. Click on ADSL. ADSL Configuration Window will be opened.
Select Standard:
G.DmtBisPlus
ActiveLine: Start. Click Startup
 |
| ADSL Configuration Window |
15. Click Maintenance and then on save. In save configuration, click save.
 |
| save configraions |
16. Finally, save configuration will be completed showing the following window.
 |
| Save Configrations |
17. Now restart the Router. Click on Restart.
 |
| Restart Router |
18. Go again to Internet Protocol (TCP/IP) Properties and Select Obtain an IP address
automatically and leave the DNS server addresses unchanged as shown in the picture
below and press Ok.
Now, open the Internet Explorer and start browsing the sites for successful configuration and
DSL connection establishment.
 |
| TCP IP PROTOCOL SETTINGS |
Post a Comment